示例项目,第 12 级

连接器、引脚分配和排线

带部件的插接连接器:M12 上的传感器和 M8 上的阀,GX16 和 GX12 航空插头上的风扇及其温控器,D-sub 9 上的蜂鸣器,以及两个 IDC 插座之间排线上的操作面板;插头窗口在插合面上显示每个插头的引脚分配及导线和芯线颜色。

图纸

由 OpenECraft 的 SVG 导出绘制,与项目随附时的状态一致。

8 页

页描述
1Cover sheet
2Proximity switch on M12, valve on M8
3Fan on GX aviation connectors, buzzer on D-sub
4Operator panel on ribbon cable
5Plug diagram
6Cable overview
7Cable diagram
8Bill of materials

更多示例

1 · 第一个电路:按钮和指示灯

一页原理图,包含 +24V / 0V 电位、按钮、选择开关、指示灯和熔断器;部件和物料清单。

查看示例

2 · 带自锁触点的继电器

带继电器的启动 / 停止电路:线圈和触点组成一个设备,带交叉引用和触点映像;端子排、导线编号、端子图和连接列表。

查看示例

3 · 星三角启动器

分布在多页上的主电路和控制电路:主开关、电机保护、三个带互锁的接触器、通电延时继电器、中断点、带导线颜色的电位、电机电缆和电缆报表。

查看示例

4 · 带 PLC 和控制柜的输送机

演示项目:PLC 输入和输出、带导轨、线槽和柜门设备的机柜布置、柜门线束和电机电缆。

查看示例

5 · 电气气动压力机

流体动力与电气同在一个项目中:带气源处理单元、阀岛、5/2 阀、流量控制阀和气缸的气动回路;电磁线圈和位置开关与阀和气缸相关联。

查看示例

6 · 带结构标识符的泵站

按 IEC 81346 的工厂结构(功能和位置)、页面分节、单线图、一台直接启动的泵和一台带变频器的泵、带数字和模拟通道的 PLC 卡、一个传感器插头以及 PLC 分配。

查看示例

7 · 修订、审查和变更请求

第一次发布后的输送机:已发布并锁定的修订、此后标记的更改、带红线标注的审查注释、一个变更请求、处于审批流程中的修订 B 以及用于比较的基线。

查看示例

8 · 并柜排列的控制柜

安装在两台并柜落地柜中的泵站:母线系统、导轨和线槽、柜门设备和把手、过滤风扇、照明灯、PE 排、电缆密封接头、电缆通道、柜内温控计算、线槽填充率和三维布线。

查看示例

9 · 电气室

并柜后的控制柜在其房间中:L 形平面图、内墙、门和窗、放置到位的并柜、墙上带插座的导轨、墙装应急灯以及顶部下方的电缆桥架。

查看示例

10 · 泵房

并柜排列所在的房间及其泵:泵电机经柜顶的电缆密封接头供电,泵和储罐落地放置,球阀和压力表装在墙上,水回路的 DN25 管道沿墙面管道走线进行 3D 布线。

查看示例

11 · Building services with water supply and PV storage

A whole building in two rooms: the supply cable and the water main come in through building entries to the house connection box and the remote controlled valve; main distribution with busbars, Hager NH fuse switch disconnectors of three sizes and energy meters; cables and the water pipe pass a wall penetration into the technical room with PLC and pump cabinets, tanks and booster pumps, a compressor with air receiver and dryers and oilers at the outlets, a heat pump with buffer tank and hot water circulation, temperature, pressure and level sensors, a PV system with generator junction box, Victron MultiPlus-II and Inverter RS on the wall, Cerbo GX and Pylontech batteries in a 19-inch rack.

查看示例

13 · Transformer-rated metering with PV and grid protection

The distribution cabinet of an apartment building with an 88 kWp PV system, built from Hager univers parts: busbars with surge arrester and connection point zone, consumption and generation metering with NH1 fuse switch disconnectors on component modules, current transformers, voltage paths and meter cabinets with test terminal blocks, heat pump and inverter feeders, grid and system protection with voltage and frequency relay, buffered 24 V supply, fire brigade switch and a coupling switch with motor operator, undervoltage release and auxiliary switch built in; the cabinet comes with its plinth and lifting eyes.

查看示例

14 · Main low-voltage distribution of an industrial plant

Two bayed Hager univers cabinets: two aluminium supplies on busbar terminals for Al, transformer metering isolated by NH strips with solid links, a power analyser for the zero export of the battery storage, feeders on NH fuse switch disconnector strips of a 185 mm busbar system with current transformers clipped in behind them and energy meters on the Tree bus (DC charging station, sub-distributions, air conditioning), heat pumps behind residual current devices of type B, PV inverters and battery storage behind two coupling switches with motor operators, undervoltage releases and auxiliary switches, cable entry flanges for the large cables.

查看示例

15 · Plant with buildings, levels and a shaft

The pump room in a plant of two buildings: the main building with the electrical room on its ground level and the control room above, joined by a shaft; the pump house with pump motor 2, linked by a cable trench between the building entries through which its motor cable is routed; façade lights on the outside walls and a weather station on the roof.

查看示例

16 · 带屋顶、楼梯和安装的办公楼

The plant of level 15 with an office building: the office on the ground level and the attic under a gable roof whose slopes cut its ceiling down to the knee wall, a stair turned at a quarter landing, roof windows in the front slope; Gira socket outlets, a network outlet and a switch, an MDT KNX push button and room temperature controller, a TV outlet at their mounting heights, a COSMO heating circuit manifold and a single-room control box.

查看示例